Ice Toolz

Ice Toolz 62D1 All-in-1 Master Link Tool Review

As a long time master link user, Campagnolo peen chain hater, and an S&S coupled frame owner, I was really excited to get my hands on a set of these.  In my eyes it was a way to reduce the amount to tools I needed to have and also pack when I go on trips with my S&S bike (this is because I remove the chain every time). 

The Ice Toolz 62D1 All-in-1 Master Link or Missing Link Tool

The Ice Toolz 62D1 All-in-1 Master Link or Missing Link Tool

DESIGN

The design of the tool is simple, and the unit is well constructed.  The hand grips are soft and feel great in the hand.  The tool is smooth and changes from "Open" to "Close" modes with ease and precision.  Overall it really seemed like a great tool.  However, there is a significant design flaw.  Ice Toolz must have not tested 11 speed Master Links, because this tool will not work in "Close" mode with them.  The end of the tool is not narrow enough to fit in between the rollers.  This resulted in me not using the tool as intended to install my KMC 11 speed chain.  It still works but it's a lot more effort to pull the master link into position that squeeze it as intended.  On the flip side the "Open" function works great, but due to the struggle on the "Close" end of things, I would recommend looking for a different tool. 

The 62D1 opens the links no problem.

The 62D1 opens the links no problem.

The 62D1 does not fit in the 11s to lock it into place.   The chain opening is too narrow for both tips to fit

The 62D1 does not fit in the 11s to lock it into place.   The chain opening is too narrow for both tips to fit

Below is the work around I used to close the chain.  You can move each tip to outside of the Missing Link and instead of squeezing to lock the link into place, you pull the handles apart.  This works pretty good, but it does take some extra effort as squeezing is far easier that pulling.  Also, you have to be careful as the tips can slip out due to the lack of grooves for the rollers on the chain to sit in.  

The 62D1 Work Around.  Does not work that well because the tips can slip out easy since there aren't cavities

The 62D1 Work Around.  Does not work that well because the tips can slip out easy since there aren't cavities

PRICE

Because the design flaw, it doesn't really how much you buy these for, it's still too high.  I was able to get mine for a smoking deal direct from Ice Toolz, but I still feel ripped off because of the fact they don't work how they are supposed to with my 11 speed drive train. 

CONCLUSION 

Overall, this tool misses the mark.  As more companies are moving towards and pushing 11 speed and narrower chains, Ice Toolz better do right by the consumer and update their outdated tool.  My next purchase, and what seems to be a far better option will be the Super B TB-3323.    

2.0_of_5.0.png

Park Tool HTR-1B vs Ice Toolz E181 Reamer Review

This is something I have been wanting to do for a long time.  As a person who over analyzes every purchase I've ever made, I can understand how important reviews are for the modern day consumer.  My goal is that some of the things I say will help add more information to this community and possibly help people make decisions on what products they should use.  All my reviews are 100% honest based on my own experiences.  

The first 4 frames I built I used an Ice Toolz E181 Reamer.  It is a decent tool, but I wish I would have saved my money.  While the Ice Toolz reamer did the job, you can tell it was not quite manufactured to the highest standards.  

One of the most frustrating things I noticed was the threaded rod for the guide cone came out of the upper handle at a slight angle.  This meant that the facer never sat flat on the HT, and only a few teeth would always do the cutting.  It also meant the reaming was not done exactly perpendicular to the Head Tube.  While this never caused a problem, it annoyed me every time I used it.  I will say that this was not because the threaded rod was bent, but actually because the hole was drilled at an angle in the handle.  Trust me I tired to fix this issue.  

One thing I did like about the Ice Toolz E181 was the fact the handles unscrewed from the handle body.  This was nice for storing the tool as I would only break it out every month or so.  The case was actually a pretty nice touch too, something I wish my Cyclus and Park tools had as most of my tools are not hung on a wall.   

Ultimately the Ice Toolz E181 did work, and maybe I just received a bad unit that slipped through QC.  However, if I could go back in time I would have probably just saved one extra paycheck for the PARK HTR-1B, which I actually end up buying on Ebay for about the same price.

1" HT Reamed and faced with the Ice Toolz Reamer.  This is the 3rd frame it was used on.

Ice Toolz Reamer, you can see the chip accumulation in one area.  This is the only part of the tool that touches the HT as a result of inconsistent manufacturing. 

The PARK HTR-1B is a far better tool.  It's built a lot better and you can just feel that when you pick it up.  In addition, the lower guide cone design is 1000X better. This makes reaming/facing a lot smoother with less effort.  One thing I don't like about the HTR-1B is the handles are welded.  For someone who always seems to not have enough tool space, it would be nice if the handles could be unscrewed for storage.  This is a tool I'm not using all the time since my volumes are fairly low, so I usually like to tuck it safely away in my tool box.  The cutters and the HTR-1B are quite nice, and they do a good job of making round holes for easy HS pressing.  In reference to the cutter there are no anti-rotation features on the reaming cutter and it can slip from time to time, which can be a little annoying.  I think Chris King takes the correct approach by splitting up the two operations.  It might take a bit longer, but the end result is improved.  

Park HTR-1B with the Chris King 44mm HT Reaming Kit

The Park tool HTR-1B with the Chris King 44mm HT Reaming tools.  This is a perfect combination for a clean cut on a 44mm Head Tube

Although there are a few nuances, the Park HTR-1B is a well designed tool for the professional builder and I highly recommend it for hobby builders as well.  Although you will save initially with the Ice Toolz setup, you will ultimately pay for it in the end.  Plus the resale value on the Park is a lot higher if you decide that framebuilding is not for you. 

For those of you need a 44mm solution, look no further than the Chris King 44mm HT Reamer.  It's probably the best setup out of any reamers on the market.  The quality of the manufacturing is top notch, it's become one of my favorite tools.

Verdict_5stars.png